FL/ITC Single Classify Wheel ClassifierChicken protein

In a rapid development of rapid development, many people have had a certain understanding of FL / ITC Single Classify, and crusher technology is in an absolute leader in the industry.

FL / ITC Single Classify Wheel Classifierchicken Protein is mainly used for more refined materials. The fractional particle size is 1.5 to 0.005 mm, and the crude material is sieved. The principle of pulverization is substantially the same as the hydraulic level, and the above settlement theory can also be used for airflow classification. However, in the airflow classification, since the density and viscosity of the air are much smaller than the density and viscosity of water, the same particles are more settled in the air than in the water. Moreover, the density and viscosity of the air vary with temperature and pressure. In order to cause air flow, wind grading equipment typically requires an appropriate fan (exhaust or blast). When the airflow is classified, the fine particles are usually taken away by the airflow. In some cases, the feedstock is sent to the grading device with the airflow. It is well known that the load of solid particles in the air under normal pressure does not exceed 500 g / m3 air. When it reaches 1 kg / m3, the particles fall from the airflow. The load is related to the density and particle size of the particles. When the fine particle material is treated, the load generally does not exceed 200 to 300 g / 3 air. According to this calculation, the volume concentration in the gas stream is much smaller than 0.03. Therefore, when the airflow is classified, in most cases, it belongs to the free settlement. The speed required to move the particulate material in the horizontal and vertical directions is relatively large, and the speed required in the horizontal direction is relatively large, and as the particle density increases, for example, for puls with a density of 1.5. Gram / cubic centimeter. The minimum wind speed is 2 m / sec; a powder material having a density of 2.5 g / cm, the speed is not less than 3.5 m / sec; a powder having a density of 4 g / cm 3, a minimum speed of 4 meters per second. Due to the complexity of the situation, the appropriate airflow rate in each particular situation should be determined by experiments. In the rising airflow, the water flow rate required to suspend a certain density and particle size is greater than the calculated value of the free settling, which is due to the uneven distribution of the airflow along the graded chamber portion. This FL / ITC Single Classify WheelClassifierchicken Protein has a high grading range, high grading efficiency, high level precision, accurate cutting particle size, and good stability.

FL / ITC Single Classify Wheel Classifierchicken Protein has the following advantages: The ultrafine classifier is achieved by a pneumatic conveyor, a high-speed collision to achieve a purpose. With wind energy, it will be powdered once, and the traditional screening procedure is canceled. Each independent operation, complete function, compact structure, stable technology, high noise, high efficiency, beautiful appearance, flexible use, wide adaptation, non-powder, adjustable powder, easy to repair, smash And dry non-fibrous materials and minerals have the ideal effect.

FL / ITC Single Classify Wheel Classifierchicken Protein's daily maintenance is a very important part, which introduces the maintenance method of FL / ITC Single Classify Wheel Classifierchicken Protein. 1. When the machine is started or started, the appropriate amount of grease should be applied to ensure its life. 2. Check if the screws and nuts of each component are fastened. Check if the belt is stuck, whether it is tight. 3, regularly check the reliability of the equipment, prevent accidents or accidents. 4. The direction of operation of the spindle should be correct. If it is incorrect, it should be handled in time to avoid damage to the machine. 5, equipment maintenance should be carried out by professional and technical personnel, other people must not be carried out to avoid damage to the equipment. 6, electrical components and lines should be checked regularly, whether it is intact, whether the ground is reliable. 7. The equipment should be cleaned in time to prevent the next use to avoid contamination materials.

Welcome everyone to choose our Shandong AlPa, company specializing in the production and development and service of gas flow crusher products, the company provides customers with safe and reliable FL / ITC Single Classify Wheel Classifierchicken Protein's products and services, solved The worries of our customers.